Resetting your Holosun EPS Carry red dot sight to its original state can be a useful tool for troubleshooting issues or simply starting fresh. The process is fairly straightforward and only requires a few simple steps. Begin with locating the reset button on the back of the sight. This small lever is often unmarked but can be easily identified by its position.
- To initiate a factory reset, you'll need to hold down the reset button for a specific duration of approximately 4 seconds. You should see a changing illumination pattern on the sight indicating that the reset process is active.
- After the completion is complete, the display will return to its normal state.
- Your Holosun EPS Carry is now completely reinitialized. You can then proceed with configuring it according to your desired setup.
Remember, always consult the user manual for specific instructions and details regarding your Holosun EPS Carry red dot sight.
Restoring Your Holosun EPS Carry to Original Settings
Need to Modify your Holosun EPS Carry Sight back to its Starting configuration? It's Straightforward. Here's how:
First, ensure the Hologram is Activated. Then, locate the Control labeled "Mode".
Press and hold this Switch for approximately 5 seconds.
You should Detect a series of Flashes on the Lens. This indicates that the Holosun is now Back to Factory Settings to its Original configuration.
Once complete, release the Control. Your Holosun EPS Carry is now Functional with all settings at their Starting values.
Calibrating the Holosun EPS Carry Red Dot Sight
The Holosun EPS Carry Green dot sight is a popular choice for concealed carry applications due to its compact size and durable construction. However, like any optical device, it may require periodic adjustment. This can be easily accomplished by following these simple steps: First, find the adjustment screws on the side of the sight. These are typically located near the battery compartment. Using a small tool, carefully turn the screws to modify the point of impact. Initiate by making small adjustments and test fire the sight at various distances to ensure accuracy. Continue this process until you achieve a desired zeroing point.
- Note that the adjustment screws can be easily damaged if overtightened, so use caution when turning them.
- Confirm that the battery is fresh and properly installed before making any adjustments.
- Should you encounter difficulty zeroing your sight, consult the manufacturer's manual for further assistance or contact Holosun customer support.
Reset Factory Settings for Holosun EPS Carry
To restore your Holosun EPS Carry to its factory settings, you will need to navigate through the sight's menu system. First, activate the optic by engaging the switch located near the side of the unit. Next, utilize the adjustable buttons found beside the holographic display to access the settings menu. Within the menu, locate the "Factory Reset" option and confirm it using the designated button. The EPS Carry will then undergo a reset sequence, which may take a few moments. Once complete, your sight will be restored to its default configuration.
- Note: During the reset process, all user-configured settings will be erased.
Clear Your Holosun EPS Carry in a Flash
Need to get your Holosun EPS Carry back to factory settings? It's easier than you think! Here are the simple steps you need to follow:
First, turn off your red dot. Then, find the tiny reset button on the side of the sight. Use a small implement like a paperclip or a pin to press and depress the reset button for about 5 seconds. You'll know it worked when the display starts flashing.
- Allow the sight to cycle through its startup sequence. This might take a few moments.
- You've successfully reset your Holosun EPS Carry to its original settings!
Reset a Holosun EPS Carry Red Dot
Need to acquire a freshstart/clean slate? Here's how you can to restore factory defaults your Holosun EPS Carry Red Dot.
First, ensure the red dot is powered factory reset Holosun EPS Carry red dot on. Next, find the tiny button on the left/right side of the sight's housing/body. Maintain a continuous press on this button for at least 5 seconds/3 seconds. You should see a flashing light/blinking indicator indicating that the reset process has begun/started. Keep holding/pressing the button until the light stops blinking/flashing. Let go the button and your Holosun EPS Carry Red Dot is now restored to factory settings.